Solar | Installation | | HelioBond PVA 600BT
|
| HelioBond PVA 600BT |
High Bond Thermal Setting Adhesive Tape |
|
HelioBond™ PVA 600BT is an extruded black butyl adhesive tape designed to provide high strength, watertight attachment of PV modules and PV pre-assemblies to single ply EPDM, TPO and metal roofing panels. It is also suitable for use on properly prepared granulated and non-granulated modified bitumen roofing. HelioBond™ PVA 600BT is designed for quick grab to roof membranes without the need for primers, yet possesses high strength at 185°F (85°C). HelioBond™ PVA 600BT also exhibits excellent adhesion to polar and non-polar substrates such as glass, metals, wood, concrete, masonry and plastics. |
|
| Physical Properties |
| |
Typical Values |
Test Method |
| Color |
Black |
Visual |
| Brittleness Temperature |
-50°F |
ASTM D 746 |
| Elongation (tape) |
> 1000% |
ASTM D 412 |
| Specific Gravity |
0.97 |
ASTM D 71 |
| Typical Aged Adhesive Strength* |
| Peel Strength |
10 pli @ 70°F 5 pli @ 190F |
| Shear Strength |
5 psi @ 190°F |
| Application Properties |
| Service Temperature |
-40°F - 250°F(-40°C – 121°C) |
ASTM D 3359 |
| Application Temperature |
40°F - 120°F(4°C – 49°C) |
ASTM C 603 |
| StorageTemperature |
68°F - 120°F (20°C – 49°C) |
ASTM D 1337 |
| Minimum Shelf Life |
1 Year |
ASTM D 1337 |
| NOTE: The foregoing information is published as general information only. The listed properties and performance characteristics are approximate values and are not part of the product specification. *Adhesive strength is dependent on many factors including substrates, application conditions and dwell time among others. |
|
| Environmentally Safe |
No primers needed, No VOC’s |
| Peel and stick |
Lowers labor costs, Decreases application time |
| Safety Benefits |
No Solvents or Torches needed |
| Excellent Tack |
Quick stick, |
| Excellent Environmental Resistance |
Impervious to water, sunshine, snow and hail |
| Proven Performance |
Years of use under the toughest rooftop environments |
| Easy release liner |
Makes installations easier, liner releases easily under rooftop conditions |
|
Basic Uses
For adhering flexible PV modules and PV pre-assemblies to EPDM and TPO membrane, metal and modified bitumen roofing substrates.
Availability/Cost
Availability and cost can be obtained from your local ADCO Products, Inc. representative or distributor.
Application Instructions
Refer to ADCO Products, Inc. application procedures
|
|
|
Caution
All statements and technical information in this document are based on tests or data that ADCO believes is reliable. However, ADCO does not warrant or guarantee the accuracy or completeness of this information. The user has sole knowledge and control of factors that can affect the performance of ADCO’s products in the user’s intended application. It is the user’s responsibility to conduct tests to determine the compatibility of ADCO’s product with the design, structure, and materials of the user’s end product and the suitability of ADCO’s product for the user’s method of application and intended use. The user assumes all risk and liability arising out of such use.
Precautions and Limitations
Talc, dust, oil, ice, snow or wet conditions inhibit good adhesion. Clean and dry surfaces are a necessity.
Check with your ADCO representative for a list of approved PV modules, roofing membranes and other substrates prior to using the 600BT for any application.
|
|
|
 |
 |
