Roofing | Modified Bitumen Accessories | Lap & Flashing Adhesive | Millennium Hurricane Force® Lap and Flashing Adhesive
|
| Millennium Hurricane Force® Lap and Flashing Adhesive |
|
|
|
Millennium Hurricane Force® Lap and Flashing Adhesive is a fast setting, solvent free, cold process adhesive, that becomes waterproof within minutes of application.
Millennium Hurricane Force® Lap and Flashing Adhesive is a low odor formula that offers significant advantages over high odor, slow setting, solvent based adhesive.
|
|
|
Ready to use
|
Requires no mixing, reduces labor costs
|
|
No temperature restrictions
|
Quick set even in cold climates
|
|
One Step™ technology
|
Easy to apply
|
|
Solvent free
|
VOC free, no odors
|
|
Elastomeric
|
Remains flexible, absorbs stresses
|
|
High build formulation
|
Suitable for vertical applications, won’t run
|
|
|
Millennium Hurricane Force® Lap and Flashing Adhesive is designed for use as an adhesive for bonding flashings and side/end laps in approved membranes.
With a utility knife, remove the molded tips at the groove from the One Step™ mixing head.
Attach a One Step™ mixing nozzle to the threaded mixing head.Place the cartridge into the appropriate One Step™ applicator. Always load cartridges with the label side up. Dispense an intial amount of Millennium Hurricane Force® Lap and Flashing Adhesive to ensure a proper mix, then discard.
For lap adhesive installation apply Millennium Hurricane Force® Lap and Flashing Adhesive in one continuous 3/4" - 1" (1.9cm - 2.5cm) wide bead down the center of the membrane’s selvage edge. As adhesive is applied immediately set membrane into wet adhesive. For flashing installation apply adhesive to the back side of the membrane in a ribbon pattern. Spread adhesive with a 1/4" x 1/4" (0.6cm - 0.6cm) square notched trowel for full coverage applications. Immediately set flashing membrane in place.
Immediately roll with weighted roller to ensure positive contact between adhesive and membrane.
Unused adhesive can be applied at a later date by simply plugging the cartridges (with provided half moon plugs) and using a new One Step™ mixing nozzle.
Approved Membranes
Approved Substrates
-
Block/brick masonry
-
Asphaltic base sheets
-
Approved insulations
-
Plywood
For a complete list of approved, membranes, substrates and insulation types, or for additional information, contact our Technical Department.
Color
Equipment
The fast and dependable One Step™ applicators make applying Millennium Hurricane Force® Lap and Flashing Adhesive simple:
-
Battery Powered Single Bead
Limitations
-
Do not apply to wet or damp surfaces.
-
Not intended for insulation attachment.
Surface Preparation
All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, loose and/or embedded gravel, un-adhered coatings, deteriorated membrane and other contaminants that may result in a surface that is not sound or is uneven.
|
Millennium Hurricane Force® Lap and Flashing Adhesive is available in the following package:
Cartridge Size Part# Cartridges/Case
1.5 Liter HF-LF15-04 4
Each cartridge will produce approximately of 50 - 75 lineal feet (15m - 23m) of 3/4" - 1" (1.9cm - 2.5cm) wide adhesive beads. Coverage rates may vary when used over irregular surfaces.
|
Storage
Keep temperature of contents between 65°F-85°F (18°C-29°C) 24 hours prior to use. Do not store in direct sunlight or temperatures higher than 90°F (32°C).
|
Prior to working with this or any product consult product label and Material Safety Data Sheet (MSDS) for necessary health and safety precautions.
CAUTION:
All statements and technical information in this document are based on tests or data that ADCO believes is reliable. However, ADCO does not warrant or guarantee the accuracy or completeness of this information. The user has sole knowledge and control offactors that can affect the performance of ADCO’s products in the user’s intended application. It is the user’s responsibility toconduct tests to determine the compatibility of ADCO’s product with the design, structure, and materials of the user’s end product and the suitability of ADCO’s product for the user’s method of application and intended use. The user assumes all risk and liability arising out of such use.
|
|
|
|
|
 |
 |
