Roofing | Modified Bitumen Accessories | Membrane Adhesive | Millennium Hurricane Force® Membrane Adhesive
|
| Millennium Hurricane Force® Membrane Adhesive |
|
|
|
Millennium Hurricane Force® Membrane Adhesive is a fast setting, solvent free, cold process membrane adhesive, that becomes waterproof within minutes of application, and is designed for use with our patented application process.*
Our One Step application process eliminates error due to poor mixing. Application is quick and easy, resulting in significant labor savings for the contractor. No expensive specialty pumps or spray rigs are required.
|
|
Ready to use
|
Requires no mixing, reduces labor costs
|
|
No temperature restrictions
|
Quick set even in cold climates
|
|
One Step™ technology
|
Easy to apply
|
|
Solvent free
|
VOC free, no odors
|
|
Elastomeric
|
Remains flexible, absorbs stresses
|
|
2-component technology
|
Fast setting, yet allows for repositioning of membrane
|
|
Ribbon applied
|
Eliminates blistering
|
Surface Preparation
All work surfaces should be clean, dry, and free of dirt, dust, debris, oils, loose and/or embedded gravel, un-adhered coatings, deteriorated membrane and other contaminants that may result in a surface that is not sound or is uneven.
For re-cover applications apply Millennium Universal Primer prior to the application of Millennium Hurricane Force® Membrane Adhesive. For applications over fresh and/or non-oxidized asphalt, coal tar or plastic film membranes, apply Millennium Surface Treatment prior to the application of Millennium Hurricane Force® Membrane Adhesive.
|
Millennium Hurricane Force® Membrane Adhesive is designed for use as an adhesive for bonding approved base sheets, vapor retarders and membranes to approved substrates.
Millennium Hurricane Force® Membrane Adhesive is a low odor, quick setting, solvent free, formula that offers significant advantages over high odor, slow setting, solvent based adhesives.
With a utility knife, remove the molded tips at the groove from the One Step™ mixing head.
Attach a One Step™ mixing nozzle to the threaded mixing head.Place the cartridge into the appropriate One Step™ applicator. Always load cartridges with the
label side up. Dispense an intial amount of Millennium Hurricane Force®
Membrane Adhesive to ensure a proper mix, then discard.
Apply Millennium Hurricane Force® membrane Adhesive directly to the substrate, using a ribbon pattern. Space 1/2" - 3/4" (1.3cm - 1.9cm) wide beads either 12" (30cm), 9" (23cm), 6" (15cm) o.c. (or in full coverage) to achieve proper coverage depending on project specifications and requirements. As adhesive is applied, immediately set membrane into wet adhesive. Do not allow the adhesive to skin over. Eliminate uneven surfaces to ensure positive contact between the membrane and substrate.
Immediately broom roll with weighted roller to ensure positive contact between adhesive, membrane, and substrate and to eliminate the possibility of ridging.
Unused adhesive can be applied at a later date by simply plugging the cartridges (with provided half moon plugs) and using a new One Step™ mixing nozzle.
Approved Substrates
• Structural roof decking: concrete, gypsum, cemetitious wood fiber (tectum), wood, steel or lightweight insulating concrete
• Base sheets ( sanded or granule surfaced)
• Approved insulations (multi-layer applications)
• Smooth built-up roof surfaces (re-roof applications)
For a complete list of approved substrates, or for additional information, contact our Technical Department.
Equipment
The fast and dependable One StepTM applicators make applying Millennium Hurricane Force® Membrane Adhesive simple:
• Patented Multi-Bead Plus*
• Battery Powered Single Bead
• Pneumatic Single Bead
Color
• Black
Limitations
• Do not apply to wet or damp surfaces.
• Not intended for insulation attachment.
|
Packaging and Coverage
Millennium Hurricane Force® Membrane Adhesive is available in the following package:
Cartridge Size Part# Cartridges/Case
1.5 Liter HF-MA15-04 4
Each cartridge will produce approximately 100 - 125 lineal feet (30m - 38m) of 1/2" - 3/4" (1.3cm - 1.9cm) wide adhesive beads.
A four cartridge case will produce approximately 400 - 500 lineal feet (122m - 152m) of 1/2" - 3/4" (1.3cm - 1.9cm) wide adhesive beads.
Coverage rates may vary when used over irregular surfaces.
|
Storage
Keep temperature of contents between 65°F-85°F (18°C-29°C) 24 hours prior to use. Do not store in direct sunlight or temperatures higher than 90°F (32°C).
|
Safety
Prior to working with this or any product consult product label and Material Safety Data Sheet (MSDS) for necessary health and safety precautions.
CAUTION:
All statements and technical information in this document are based on tests or data that ADCO believes is reliable. However, ADCO does not warrant or guarantee the accuracy or completeness of this information. The user has sole knowledge and control offactors that can affect the performance of ADCO’s products in the user’s intended application. It is the user’s responsibility toconduct tests to determine the compatibility of ADCO’s product with the design, structure, and materials of the user’s end product and the suitability of ADCO’s product for the user’s method of application and intended use. The user assumes all risk and liability arising out of such use.
|
|
|
|
|
 |
 |
